Spiral-curve-spiral stations
The , , , and stations of a circular curve with equal spirals at each end, with the total tangent, the circular arc left between the spirals, and the whole length.
Experimental: not yet fully verified. How results are checked
The spiral runs TS 115+37.79 to SC 116+87.79, the arc to CS 119+84.59, and the spiral out to ST 121+34.59.
- SC station
- CS station
- ST station
- Total tangent Ts
- Circular arc
- Total length
Provenance
- Computed by
- survey.curves.spiral-curve-spiral 1.0.0, core 0.1.0
- Model
- θs = Ls / (2R); Ts = (R + p)·tan(Δ/2) + k with p and k from the spiral's series coordinates; TS = PI − Ts, SC = TS + Ls, CS = SC + R·(Δ − 2θs), ST = CS + Ls (Ghilani & Wolf 2021, spiral curves)
- Accuracy
- The clothoid series is carried to where its terms fall below 0.001 of the unit for spiral angles up to 30°
- Notes
- 1 shown with the answer
- Cites
- Ghilani, C. D., and Wolf, P. R., Pearson, Elementary Surveying: An Introduction to Geomatics
Something look off?
How we got thisFormula, worked example, sources, and proof
Model: θs = Ls / (2R); Ts = (R + p)·tan(Δ/2) + k with p and k from the spiral's series coordinates; TS = PI − Ts, SC = TS + Ls, CS = SC + R·(Δ − 2θs), ST = CS + Ls (Ghilani & Wolf 2021, spiral curves)
Accuracy: The clothoid series is carried to where its terms fall below 0.001 of the unit for spiral angles up to 30°
When to use this: Use this to station a highway or railroad curve that has an equal spiral easing into and out of the circular arc. Enter the spiral length, the radius of the circular curve, the total deflection at the PI, and the PI station. The tool returns the four control stations in order, the total tangent from the PI back to the TS, the length of circular arc left between the spirals, and the whole length from TS to ST.
Limitations: Both spirals are the same length; an unequal pair needs each half worked on its own. The total deflection must be more than twice the spiral angle, or the spirals meet and leave no circular arc, and the spiral angle is held to 30° where the series stays accurate. It gives control stations only; use the spiral tool for the deflection table and the plan.
Worked example: 150 ft spirals on an 800 ft radius, Δ 32°, PI at 118+42.50. Source: add-survey-suite spiral requirement, evaluated by numerical integration of the clothoid.
You enter
- Total deflection Δ
- 32°00'00"
- PI station
- 118+42.50
- Circular curve radius R
- 800 ft
- Spiral length Ls
- 150 ft
You get
- TS station
- 115+37.79
- SC station
- 116+87.79
- CS station
- 119+84.59
- ST station
- 121+34.59
- Total tangent Ts
- 304.71 ft
- Circular arc
- 296.804 ft
- Total length
- 596.804 ft
- Spiral angle θs
- 5°22'17.3"
Review: Not yet independently reviewed by a licensed surveyor.
Last verified: 2026-09-23, when a maintainer last confirmed this tool's sources at the issuer. See the sources ledger.
Status: version 1.0.0, core 0.1.0. See this tool in the verification report.
Checked against: 23 golden test vectors (download the test vectors, each with its source and tolerance). See how results are checked and every source.
Sources
- Elementary Surveying: An Introduction to Geomatics, Ghilani, C. D., and Wolf, P. R., Pearson, 16th edition. Chapter 24 (spiral curves: elements, stationing, and deflections).
Terms
- CS: curve to spiral
- The station where the circular curve ends and the exit spiral begins. Source: Elementary Surveying: An Introduction to Geomatics
- PI: point of intersection
- On a horizontal curve, where the two straight tangents would meet. Source: Elementary Surveying: An Introduction to Geomatics
- SC: spiral to curve
- The station where the entry spiral ends and the circular curve begins, at the curve's full radius. Source: Elementary Surveying: An Introduction to Geomatics
- ST: spiral to tangent
- The station where the exit spiral ends and the alignment is straight again. Source: Elementary Surveying: An Introduction to Geomatics
- TS: tangent to spiral
- The station where the straight tangent ends and a spiral transition begins, curving gradually from straight toward the circular curve. Source: Elementary Surveying: An Introduction to Geomatics
Experimental means this tool has not yet met the stable bar: at least 20 golden vectors, differential tests, and an independent worked example.
CS — curve to spiral
The station where the circular curve ends and the exit spiral begins.
Source: Elementary Surveying: An Introduction to Geomatics
SC — spiral to curve
The station where the entry spiral ends and the circular curve begins, at the curve's full radius.
Source: Elementary Surveying: An Introduction to Geomatics
ST — spiral to tangent
The station where the exit spiral ends and the alignment is straight again.
Source: Elementary Surveying: An Introduction to Geomatics
TS — tangent to spiral
The station where the straight tangent ends and a spiral transition begins, curving gradually from straight toward the circular curve.
Source: Elementary Surveying: An Introduction to Geomatics