geoprimsField-grade geospatial math

Vertical curve high or low point

The station and elevation of the high point of a crest curve or the low point of a sag curve, and how far it is past the .

25+30.00

The low point is at 25+30.00, elevation 614.5 ft, 280 ft past the PVC.

High or low point elevation
Distance past the PVC
Turning point
K value
Provenance
Computed by
survey.curves.vertical-curve-turning-point 1.0.0, core 0.1.0
Model
x = −g1·L / (g2 − g1) from the PVC, where the grade g1 + (g2 − g1)·x / L is zero; elevation = PVC elevation + g1·x + (g2 − g1)·x² / (2L), grades as ratios (Ghilani & Wolf 2021, ch. 25)
Accuracy
Exact for a symmetrical parabolic curve
Notes
None
Cites
Ghilani, C. D., and Wolf, P. R., Pearson, Elementary Surveying: An Introduction to Geomatics; American Association of State Highway and Transportation Officials, A Policy on Geometric Design of Highways and Streets (the Green Book)

Something look off?

Your values

Showing an example. Change anything.
More options 1
Run many at once from a CSV

Loading…

How we got thisFormula, worked example, sources, and proof

Model: x = −g1·L / (g2 − g1) from the PVC, where the grade g1 + (g2 − g1)·x / L is zero; elevation = PVC elevation + g1·x + (g2 − g1)·x² / (2L), grades as ratios (Ghilani & Wolf 2021, ch. 25)

Show your work

  1. Algebraic difference

    A = g2 − g1, in percent

    1.5% − -3.5% = 5%

  2. Rate of change

    K = L / |A|, the length per percent of grade change

    400 ft / 5% = 80 ft per %

  3. Low point

    x = −g1 × L / A from the PVC, where the grade reaches zero

    −-3.5% × 400 ft / 5%, from station 22+50.00 = 25+30.00

The same steps an agent gets from the MCP server with explain: true.

Accuracy: Exact for a symmetrical parabolic curve

When to use this: Use this to find where water collects on a sag curve or where a crest curve tops out, to place a drainage inlet or check clearance. Enter the incoming and outgoing grades in percent, the curve length or its K value, and the PVI station and elevation. The tool returns the station and elevation of the high or low point and its distance past the start of the curve.

Limitations: A curve has a high or low point inside it only when its two grades have opposite signs; otherwise the highest and lowest points are its ends, and the tool says so instead of returning a point. The curve is an equal-tangent parabola, so use the unequal vertical curve tool for an unsymmetrical one. Elevations are along the design profile, not the ground.

Worked example: A sag from −3.5% to +1.5% over 400 ft. Source: Arithmetic on the parabola: low point 280 ft past the PVC, at 25+30, elevation 614.50 ft.

You enter

Incoming grade g1
-3.5
Outgoing grade g2
1.5
Curve length L
400 ft
PVI elevation
612.40 ft
PVI station
24+50

You get

High or low point station
25+30.00
High or low point elevation
614.5 ft
Distance past the PVC
280 ft
Turning point
low
K value
80

Review: Not yet independently reviewed by a licensed surveyor.

Last verified: 2026-09-20, when a maintainer last confirmed this tool's sources at the issuer. See the sources ledger.

Status: version 1.0.0, core 0.1.0. See this tool in the verification report.

Checked against: 24 golden test vectors (download the test vectors, each with its source and tolerance). See how results are checked and every source.

Sources

Terms

PVC: point of vertical curvature
On a vertical curve, where the curve leaves the incoming grade. Source: Elementary Surveying: An Introduction to Geomatics
PVI: point of vertical intersection
On a vertical curve, where the two grade lines would meet. Source: Elementary Surveying: An Introduction to Geomatics

PVC — point of vertical curvature

On a vertical curve, where the curve leaves the incoming grade.

Source: Elementary Surveying: An Introduction to Geomatics