geoprimsField-grade geospatial math

Wind limit at flying height

The wind and gust at your flying height from a reported wind, by the power law for your terrain, against the drone’s wind rating, with the margin left and your groundspeed into the wind.

Planning and education aid. Not for primary navigation. Full disclaimer

5.3m/s

At your height the wind is about 5.3 m/s, against a limit of 8.9 m/s. Gusts near buildings, trees, and hills are not modeled.

Shear exponent α
Wind limit used
Margin to the limit
Status
Model
Provenance
Computed by
drone.ops.wind-limit 1.1.0, core 0.1.0
Model
Power law V(h) = V_ref × (h / h_ref)^α (NREL/TP-5000-63696, section 5.3.2), with α = 1/7 over open terrain (NREL/SR-440-22223) or the terrain's textbook exponent from NREL Table 1; the gust is scaled by the same factor. Limit = wind rating, or maximum airspeed × (1 − margin); margin = limit − the stronger of wind and gust at height; groundspeed into the wind = maximum airspeed − wind at height
Accuracy
The power law is a planning estimate for a steady, well-mixed wind over even terrain. Real profiles vary with stability, time of day, and obstacles; light winds often shear more than the exponent says.
Notes
None
Cites
Olsen, T., and Preus, R., National Renewable Energy Laboratory, Small Wind Site Assessment Guidelines; AWS Scientific, Inc., for the National Renewable Energy Laboratory, Wind Resource Assessment Handbook; New York State Energy Research and Development Authority, Customer Sited Wind Handbook

Something look off?

Your values

Showing an example. Change anything.
More options 4
Drone profiles

Loading…

Run many at once from a CSV

Loading…

Wind 5.3 m/sLimit 8.9 m/sAt 110 ft: margin 3.6 m/sReported 11.7 mph at 100 ft; α = 0.23Gusts near buildings are not modeled.
How we got thisFormula, worked example, sources, and proof

Model: Power law V(h) = V_ref × (h / h_ref)^α (NREL/TP-5000-63696, section 5.3.2), with α = 1/7 over open terrain (NREL/SR-440-22223) or the terrain's textbook exponent from NREL Table 1; the gust is scaled by the same factor. Limit = wind rating, or maximum airspeed × (1 − margin); margin = limit − the stronger of wind and gust at height; groundspeed into the wind = maximum airspeed − wind at height

Show your work

  1. Shear exponent

    α for the terrain (NREL), or yours

    your exponent = 0.23

  2. Height factor

    (flying height / report height)^α

    (33.5 m / 30.5 m)^0.23 = 1.0222

  3. Wind at height

    reported wind × height factor

    5.23 m/s × 1.0222 = 5.3 m/s

The same steps an agent gets from the MCP server with explain: true.

Accuracy: The power law is a planning estimate for a steady, well-mixed wind over even terrain. Real profiles vary with stability, time of day, and obstacles; light winds often shear more than the exponent says.

When to use this: Use this before a flight when the wind is reported at a weather station, usually 10 m above the ground, and you will fly higher, where it blows harder. It estimates the wind and gust at your height for your kind of terrain and sets them against your drone’s wind rating, so you can see the margin, and how fast the drone can still make progress into the wind.

Limitations: The power law describes a steady wind over even ground. Near buildings, trees, cliffs, and ridges the wind speeds up, slows down, and turns in ways it does not model, and a gust is a moment, not a profile, so scaling it by the same factor is a rough guide. The terrain exponents are textbook values; a measured profile beats them. A drone's wind rating is the maker's test figure, not a guarantee in turbulence or with a payload.

Worked example: NYSERDA's wind estimate at 110 ft. Source: NYSERDA Customer Sited Wind Handbook, section 6.2, page 33: α = 0.230 gives 12.0 mph at 110 ft from 11.7 mph at 100 ft. It is golden test vector v008, and every build checks the tool still gives its answer within its tolerance.

You enter

Shear exponent α
0.23
Flying height
110 ft
Report height
100 ft
Drone wind rating
20 mph
Reported wind
11.7 mph

You get

Wind at height
5.3 m/s
Shear exponent α
0.23
Wind limit used
8.9 m/s
Margin to the limit
3.6 m/s
Status
within the limit
Model
Power law with α = 0.23 (your exponent). Gusts and turbulence near buildings, trees, and terrain are not modeled.

Review: Not yet independently reviewed by a Part 107 remote pilot.

Last verified: 2026-09-25, when a maintainer last confirmed this tool's sources at the issuer. See the sources ledger.

Status: version 1.1.0, core 0.1.0. See this tool in the verification report.

Changes

Checked against: 22 golden test vectors (download the test vectors, each with its source and tolerance). See how results are checked and every source.

Constants this tool assumes

Values you do not enter, and where each comes from.

Shear exponent over calm sea
0.09 — Small Wind Site Assessment Guidelines
Shear exponent over open terrain
1/7 — Wind Resource Assessment Handbook
Shear exponent over crops or tall-grass prairie
0.19 — Small Wind Site Assessment Guidelines
Shear exponent around scattered trees and hedges
0.24 — Small Wind Site Assessment Guidelines
Shear exponent around suburbs and villages
0.31 — Small Wind Site Assessment Guidelines
Shear exponent over woodland
0.43 — Small Wind Site Assessment Guidelines
Report height when none is given (a METAR's)
10 m — Small Wind Site Assessment Guidelines

Sources