geoprimsField-grade geospatial math

Maneuvering speed and weight

Why VA drops when the airplane is light, the square-root rule, and what VA does and does not protect.

For pilots · updated 2026-10-20

Planning and education aid. Not for primary navigation. Full disclaimer

The maneuvering speed printed in most flight manuals is good for one weight: the maximum. Fly lighter and the safe number goes down, not up. That surprises a lot of pilots, because a lighter airplane feels like it should be the easier one on its wings.

The fix is one square root. Multiply the published speed by the square root of your weight over the maximum weight.

What maneuvering speed protects

The Pilot’s Handbook defines design maneuvering speed (VA) as the speed below which you can move one flight control, once, to its full deflection, in one axis, in smooth air, without risk of damage to the airplane.

Read that definition slowly. It is narrow on purpose. It does not cover full inputs in two axes at once. It does not cover a full input and then a full input the other way. The handbook says so plainly: flying at or below VA “does not provide structural protection” against those.

So VA is a limit, not a comfort zone. It is also the speed many pilots slow to in turbulence, which is where weight starts to matter.

Why weight changes it

VA works because the wing stalls before it can break the airplane. Pull hard below VA and the wing runs out of lift (it stalls) before it makes enough load to bend anything. Above VA the wing can make more load than the structure was built to take.

How much load can a wing make before it stalls? That depends on how fast you are going compared with the stall speed. The handbook’s example: an airplane that stalls at 60 knots, stalled at 102 knots, pulls a load factor of 1.7 squared, about 2.89 g. Load factor grows with the square of the speed ratio.

Now make the airplane lighter. A lighter airplane needs less lift to fly, so it stalls at a lower speed. Stall speed goes with the square root of weight. At the same airspeed, the light airplane is flying further above its own stall speed, so a sharp pull can make more g before the wing quits.

The structure did not get stronger when you burned fuel. Its limit load factor is the same number it always was. To keep the stall arriving before that limit, the speed has to come down with the stall speed. That is the old 14 CFR 23.335(c) relation: VA is not less than VS times the square root of the limit load factor, and VS moves with the square root of weight.

How it is worked out

Put those together and the weight cancels into one ratio:

That’s it. No load factor, no stall speed, just the number in the book and two weights. A quarter of the maximum weight gives half the speed, since the square root of 1/4 is 1/2.

Older airplanes may not print VA at all. For those, the handbook offers a rough guide: about 1.7 times the normal stall speed. The 1.7 comes from √2.89, the same square-root logic run backward. Treat it as a cross-check, not a substitute for the manual.

A worked example

Take an airplane whose manual gives VA as 105 knots at its maximum weight of 2,550 lb. Today you are flying solo with partial fuel at 2,000 lb.

That is 12 knots slower than the number on the placard. If you hit turbulence and slow to 105 knots out of habit, you are above your actual maneuvering speed for the day.

Two more things to know before you lean on the result:

The maneuvering speed tool works this out for your weights, and the weight and balance tool gives you the weight to put in it. The turn tool shows the load factor a bank angle adds, which is the same load the wing is carrying when you pull.

Try it: Maneuvering speed at a weight

The calculator below is the real tool, running its worked example. Change any value; nothing leaves your device.

93kt

At this weight, maneuvering speed is 93 kt.

Weight ratio
Provenance
Computed by
aviation.performance.va-for-weight 1.0.0, core 0.1.0
Model
VA = VA,max × √(W / Wmax), derived from 14 CFR 23.335(c) (VA not less than VS √n, pre-2017 text) with VS proportional to √W; cross-check VA ≈ 1.7 VS (PHAK ch. 5)
Accuracy
Exact for the square-root relation; your flight manual governs if it publishes VA by weight
Notes
1 shown with the answer
Cites
FAA (eCFR), 14 CFR 23.335, Design airspeeds

Open the full tool, with your values →

Your values

Showing an example. Change anything.
More options 1

Tools for this

Sources

Every number on this page comes from the tools above, which cite their sources on their own pages under "How we got this." Found a mistake? Use "Report a problem" at the bottom of the page.